Product Series
Please feel free to contact us!
We look forward to your call and inquiry!
Company Address
No. 90, Weisan Road, Industrial Zone, Wen County, Jiaozuo City, Henan Province
Service Hotline
Sales call
Technical Support
Email box
ASGEXA-G5111
- Commodity name： ASGEXA-G5111
- Input： Dry contact or NAMUR-type proximity switch
- Number of channels： One in, two out
- Output： Relay contacts
- Power supply mode (both can be centralized power supply)： 24VDC
Product Details
- Product Description
-
Product Introduction
Digital input and relay‑output safety barrier: it isolates and outputs signals from dry contacts or NAMUR‑type proximity switches in the hazardous area to the safe area via isolated relay contacts. The output and input can be configured via DIP switches to operate in either non‑inverting or inverting logic (default: non‑inverting); the line‑fault monitoring function can be enabled or disabled (default: enabled, with LED blinking during a line fault); and a second output channel can be set to function as a relay output or as a fault‑alarm output. This product requires an independent power supply and features three‑terminal isolation between input, output, and power.
Technical Specifications
- Power Supply: 18 VDC to 32 VDC, with reverse polarity protection.
- Operating power consumption: ≤1W
- Input signal: dry contact or NAMUR-type proximity switch
- Switching characteristics: When the input current exceeds 2.1 mA, the output relay closes and the channel indicator light remains steadily illuminated in yellow; when the input current falls below 1.2 mA, the output relay opens and the channel indicator light turns off.
- Open-circuit voltage: approximately 8.5 V
- Short-circuit current: approximately 8.5 mA
- Output signal: relay contacts
- Allowable load: 250 VAC/2 A or 30 VDC/2 A
- Line fault: If the input current is ≤50 μA, a broken‑wire condition is detected and the output relay trips; if the input current is ≥6.5 mA, a short circuit is detected and the output relay trips, with the channel indicator flashing red.
- Switch life: >100,000 cycles
- Switching frequency: <10 Hz
- Response time: <20ms
- Electromagnetic Compatibility: IEC 61326-3-1
- Dielectric strength: ≥2500 VAC (between intrinsically safe side and non‑intrinsically safe side); ≥1500 VAC (between power supply and non‑intrinsically safe side)
- Insulation resistance: ≥100 MΩ (input/output/power supply)
- Operating temperature: -20°C to +60°C
- Storage temperature: -40°C to +80°C
- Dimensions: 12.7 mm wide × 110 mm high × 118.9 mm deep
- Application: Installed in the safety zone, it can be connected to intrinsically safe equipment in Zones 0, 1, and 2; IIA, IIB, and IIC; and T1 through T6 hazardous areas.
Product Introduction
Digital input and relay‑output safety barrier: it isolates and outputs signals from dry contacts or NAMUR‑type proximity switches in the hazardous area to the safe area via isolated relay contacts. The output and input can be configured via DIP switches to operate in either non‑inverting or inverting logic (default: non‑inverting); the line‑fault monitoring function can be enabled or disabled (default: enabled, with LED blinking during a line fault); and a second output channel can be set to function as a relay output or as a fault‑alarm output. This product requires an independent power supply and features three‑terminal isolation between input, output, and power.
Technical Specifications
- Power Supply: 18 VDC to 32 VDC, with reverse polarity protection.
- Operating power consumption: ≤1W
- Input signal: dry contact or NAMUR-type proximity switch
- Switching characteristics: When the input current exceeds 2.1 mA, the output relay closes and the channel indicator light remains steadily illuminated in yellow; when the input current falls below 1.2 mA, the output relay opens and the channel indicator light turns off.
- Open-circuit voltage: approximately 8.5 V
- Short-circuit current: approximately 8.5 mA
- Output signal: relay contacts
- Allowable load: 250 VAC/2 A or 30 VDC/2 A
- Line fault: If the input current is ≤50 μA, a broken‑wire condition is detected and the output relay trips; if the input current is ≥6.5 mA, a short circuit is detected and the output relay trips, with the channel indicator flashing red.
- Switch life: >100,000 cycles
- Switching frequency: <10 Hz
- Response time: <20ms
- Electromagnetic Compatibility: IEC 61326-3-1
- Dielectric strength: ≥2500 VAC (between intrinsically safe side and non‑intrinsically safe side); ≥1500 VAC (between power supply and non‑intrinsically safe side)
- Insulation resistance: ≥100 MΩ (input/output/power supply)
- Operating temperature: -20°C to +60°C
- Storage temperature: -40°C to +80°C
- Dimensions: 12.7 mm wide × 110 mm high × 118.9 mm deep
- Application: Installed in the safety zone, it can be connected to intrinsically safe equipment in Zones 0, 1, and 2; IIA, IIB, and IIC; and T1 through T6 hazardous areas.
Keywords:
Please feel free to contact us!
Please provide your contact information and details, ensuring that all fields are filled in correctly. We will get in touch with you within 24 hours.
Phone:+86-(0)391-3700668
Address: No. 90, Wei San Road, Industrial Zone, Wen County, Jiaozuo City, Henan Province
WeChat Official Account